PCIe/PCI Express x1 x4 x8 x16 series
Attention:
1. Whole signals of bus Test Socket/Converter/Extender maybe not 100% one to one(1:1)
convert, please check specification.
2. No matter how many Slot/Socket, PCI series only can use one Slot/Socket at a time.
3. All Converters/Test Socket/Riser card/Extender have Timing, Delay, Impedance,
Resistance Contact problem, so we can't guarantee can work100%.
4. External converter card, if occur unstable, try to shorten the cable to better this status.
Note: Down-plugging and Up-plugging must depends on your mother board and add-in card
which PCI Express Lane of bandwidth and routed.
PCI Express cards and slots will exist with a variety of link widths.
|
PCI Express cards and slots Interoperability |
||||
| Card |
Slot |
|||
| x1 | x4 | x8 | x16 | |
| x1 | Required | Required | Required | Required |
| x4 | No | Required | Allowed | Allowed |
| x8 | No | No | Required | Allowed |
| x16 | No | No | No | Required |
 |
|
 |
 |
|
Mechanical Drawing 08pedwg.pdf |
|
| Gold Fingers / Slot Protector card | |
| * To extent the
gold fingers life. * Gold fingers pin to pin(1 to 1) connect to slot, the common pin Power and Ground didn't connect with together. |
|
| 1. CV08PE-1S(PCI Express x1=36p) | (Discontinued) |
| 2. CV08PE1-16S(x1 PCB + x16Slot) | (Discontinued) |
| 3. CV08PE-4S(PCI Express x4=64p) | (Discontinued) |
| 4. CV08PE4-16S(x4 PCB + x16Slot) | (Discontinued) |
| 5. CV08PE-8S(PCI Express x8=98p) | (Discontinued) |
| 6. CV08PE8-16S(x8 PCB + x16Slot) | (Discontinued) |
| 7. CV08PE-16S(PCI Express x16=164p) | (Discontinued) |
| 1. SH08PE-1Sv3(PCI Express x1=36p) | inquiry |
| 2. SH08PE-1Sv2(PCI Express x1=36p) | inquiry |
| 3. SH08PE1v2-4S(x1 PCB + x4 Slot) | inquiry |
| 4. SH08PE1v2-8S(x1 PCB + x8 Slot) | inquiry |
| 5. SH08PE1v2-16S(x1 PCB + x16 Slot) | inquiry |
| 6. SH08PE-4Sv2(PCI Express x4=64p) | inquiry |
| 7. SH08PE4v2-8S(x4 PCB + x16 Slot) | inquiry |
| 8. SH08PE4v2-16S(x4 PCB + x16 Slot) | inquiry |
| 9. SH08PE-4Sv3(PCI Express x4=64p) | inquiry |
| 10. SH08PE4v3-16S(x4 PCB + x16 Slot) | inquiry |
| 11. SH08PE-8Sv2(PCI Express x8=98p) | inquiry |
| 12. SH08PE8v2-16S(x8 PCB + x16 Slot) | inquiry |
| 13. SH08PE-16Sv2(PCI Express x16=164p) | inquiry |
 |
|
 |
|
 |
Mechanical Drawing 09pedwg.pdf |
| PCI Express Test Socket | ||
| * Easy for Logic Analyzer and
Oscilloscope to measure PCIe bus every pin signal. * Gold fingers pin to pin(1 to 1) connect to slot, the common pin Power and Ground didn't connect with together. |
||
| 1. CV09PE-1S(PCIe x1) | by case | inquiry |
| 2. CV09PE-4S(PCIe x4) | inquiry | |
| 3. CV09PE-8S(PCIe x8) | by case | inquiry |
| 4. CV09PE-16S(PCIe x16) | inquiry | |
| 1. SH09PE-1S(PCI Express x1=36p) | inquiry | |
| 2. SH09PE1-4S(x1 PCB + x4 Slot) | inquiry | |
| 3. SH09PE1-8S(x1 PCB + x8 Slot) | inquiry | |
| 4. SH09PE1-16S(x1 PCB + x16 Slot) | inquiry | |
| 5. SH09PE-1Sv2(PCI Express x1=36p) | inquiry | |
| 6. SH09PE1v2-16S(x1 PCB + x16 Slot) | inquiry | |
| 7. SH09PE-4S(PCI Express x1=64p) | inquiry | |
| 8. SH09PE4-8S(x4 PCB + x8 Slot) | inquiry | |
| 9. SH09PE4-16S(x4 PCB + x16 Slot) | inquiry | |
| 10. SH09PE-8S(PCI Express x8=98p) | inquiry | |
| 11. SH09PE8-16S(x8 PCB + x16 Slot) | inquiry | |
| 12. SH09PE-16S(PCI Express x16=164p) | inquiry | |
| Slot / Riser / Extender card | |
| * Change the Add-in card insert position, Form
Factor: 2U * Easy for Logic Analyzer and Oscilloscope to measure PCIe bus every pin signal. * Gold fingers pin to pin(1 to 1) connect to slot, the common pin Power and Ground didn't connect with together. * The circuit length is too long, therefore only Top Slot be able to work. (must cut the slot's Rx and Tx signals which after the one you use.) |
|
| 1. CV08PE1-Lx2(PCIe x1) | inquiry |
| 2. CV08PE4-Lx2(PCIe x4) | inquiry |
| 3. CV08PE8-Lx2(PCIe x8) | inquiry |
| 4. CV08PE16-Lx2(PCIe x16) | inquiry |
| Option: Add Stand-insert PCI slot x1 | +S Add Stand-insert slot x1 |
| Option: Add Right-angle/insert PCI slot x1 | +R Add Right-angle/insert slot x1 |
| Option: Add PH= Pin Head | +PH Add Pin Head |
(Left-insert) Left-angle/side insert slot x1, for Add-in card insert
to left side slot(Solder side up).
(Right-insert) Right-angle/side insert slot x1, for Add-in card insert
to Right-angle/side slot(Component side up).
(Stand-insert) Stand type insert slot x1, for Add-in card insert
to top side slot(No change position).
| For PCI Express 1U riser card with Alarm and Blinking led | |
|
|
 |
|
 |
Mechanical Drawing pe16ldwg.pdf |
| Slot / Riser / Extender card | |
| * Change the Add-in card insert position, Form Factor: 1U, with Test Point pads. | |
| 01. SH08PE1L(PCIe x1) | inquiry |
| 02. SH08PE1-4L(x1 PCB + x4 Slot) | inquiry |
| 03. SH08PE1-8L(x1 PCB + x8 Slot) | inquiry |
| 04. SH08PE1-16L(x1 PCB + x16 Slot) | inquiry |
| 05. SH08PE4L(PCIe x4) | inquiry |
| 06. SH08PE4-8L(x4 PCB + x8 Slot) | inquiry |
| 07. SH08PE4-16L(x4 PCB + x16 Slot) | inquiry |
| 08. SH08PE8L(PCIe x8) | inquiry |
| 09. SH08PE8-16L(x8 PCB + x16 Slot) | inquiry |
| 10. SH08PE16L(PCIe x16) | inquiry |
| Option: Add Sound and Blinking LED x2 | +S/B Add Buzzer and Red/Green Blinking LED |
| PCI Express to PCI Express external card | |
| * Extend to outside of motherboard for testing, Form
Factor: 2U * Easy for Logic Analyzer and Oscilloscope to measure PCIe bus every pin signal. * Gold fingers pin to pin(1 to 1) connect to slot, the common pin Power and Ground didn't connect with together. * with ATA-100 cable length= 45cm. * The circuit length is too long, so only for signal measurement and test. |
|
| 1. CV09PE-e1Lx2 | inquiry |
| 2. CV09PE-e1Lx2S | inquiry |
| 3. CV09PE-e4Lx2 | inquiry |
| 4. CV09PE-e4Lx2S | inquiry |
| 5. CV09PE-e8Lx2 | inquiry |
| 6. CV09PE-e8Lx2S | inquiry |
| 7. CV09PE-e16Lx2 | inquiry |
| 8. CV09PE-e16Lx2S | inquiry |
| Option: Add Stand-insert PCI slot x1 | +S Add Stand-insert slot x1 |
| Option: Add Right-angle/insert PCI slot x1 | +R Add Right-angle/insert slot x1 |
| Option: Half pitch twisted flat cable | inquiry |
| Option: Teflon flat cable | inquiry |
(Left-insert) Left-angle/side insert slot x1, for Add-in card insert
to left side slot(Solder side up).
(Right-insert) Right-angle/side insert slot x1, for Add-in card insert
to Right-angle/side slot(Component side up).
(Stand-insert) Stand type insert slot x1, for Add-in card insert
to top side slot(No change position).
| PCI Express Open-Short test card | |
| * This card manual test "Open/Short" circuits for PCIe slot and gold fingers. | |
| CV-11PE16(PCIe x16) Open/Short test card | inquiry |
| Option: Add CV09PE-1S, can testing PCIe x1 | inquiry |
| Option: Add CV09PE-4S, can testing PCIe x4 | inquiry |
| Option: Add CV09PE-8S, can testing PCIe x8 | inquiry |
The by case item( mini order 500pcs )
| Home | Index |
|
Start: 02/08/2004 Update: 04.22.2010
