DDR3 Gold Fingers Protector/Slot/Riser card/Test socket/Interposer
240p Open-Short test card
Others RAM/SDRAM/DDR/DDR2 Memory module series products
Attention:
1. Whole signals of gold fingers Protector/Slot/Riser card/Test Socket
not 100% one to one(1:1) convert, please check specification.
2. No matter how many Slot/Socket, only can use one Slot/Socket at a time.
3. All Converters/Test Socket/Riser card/Extender card have Timing, Delay, Impedance,
Resistance contact problem, so we can't guarantee can work 100%,
if any unstable, please under-Data Rate(MT/s) perhaps can improve it.
4. External Converter, if occur unstable, try to shorten the cable to better this status.
|
|
(Discontinued) |
 |
 |
 ¡@ |
| Gold Fingers
Protector * To extent the DDR3 module gold fingers or socket life. |
|
| CV08R-DDR3S (Discontinued) | |
| CV08R-DDR3S+Led (Discontinued) | |
| Option: +Led Add ReSeT#, ERR#, CK0,
CK0#, RAS#, WE#, S0#,CAS#, S1#, VDD, signal LED and the Led only light on the Power-On moment, other time is light off.¡@ |
|
| CV08R-DDR3Sv1.1 | inquiry |
| CV08R-DDR3Sv1.1+Led | inquiry |
| Option: +Led Add ReSeT#, ERR#, CK0,
CK0#, RAS#, WE#, S0#,CAS#, S1#, VDD
signal LED |
¡@ |
¡@
| Socket/Riser card * Change the DDR3 RAM Module insert position. (Right-insert) Right-angle/side Socket x1, for RAM Module insert to Right slot (Component side up). (Left-insert) Left-angle/side Socket x1, for RAM Module insert to Left slot (Solder side up). (Stand-insert) Stand type Socket x1, for RAM Module insert to Top slot (No change position). * Easy for Logic Analyzer and Oscilloscope to measure RAM Module every pin signal. |
|
| CV08R-DDR3L(Left insert socket x1) | inquiry |
| CV08R-DDR3R(Right insert socket x1) | inquiry |
| CV08R-DDR3RL-PCB | inquiry |
| Option: +Led Add ReSeT#, ERR#, CK0,
CK0#, RAS#, WE#, S0#,CAS#, S1#, VDD, signal LED and the Led only light on the Power-On moment, other time is light off. |
¡@ ¡@ ¡@ |
| Option: +L Add L-Left socket x1 | |
| Option: +R Add R-Right socket x1 | |
| Option: +S Add S-Stand/Top socket x1 | |
| Option: +PH Add PH=68p x3/4 Pin Head | |
 |
 |
| Test Socket
* Gold fingers pin to pin(1 to 1) connect to module socket, the common pin VDD(Power)/VSS(Ground) didn't connect with together. * Easy for Logic Analyzer and Oscilloscope to measure Ram Module every pin signal. |
|
| CV09R-DDR3S | inquiry |
| CV09R-DDR3S+Led | inquiry |
| CV09R-DDR3S-PCB | inquiry |
| CV09R-DDR3S-NF switch VDD power On-oF and Reset signal | inquiry |
| CV09R-DDR3S-NF+Led | inquiry |
| Option: +Led Add ReSeT#, ERR#, CK0,
CK0#, RAS#, WE#, S0#,CAS#, S1#, VDD, signal LED and the Led only light on the Power-On moment, other time is light off. |
¡@ |
| CV09DDR3-2(DDR3 to
DDR2) Gold fingers pin to pin(1 to 1) connect to another socket (no function). CV09DDR3-2-PCB Option: +DDR2S Add DDR2-240S S-Stand socket. |
inquiry |
| CV09DDR3-2K(DDR3
to DDR2) Socket pin to pin(1 to 1) connect to another socket (no function). |
inquiry |
| CV09DDR3-2K-PCB | inquiry |
 |
 |
 |
| DDR3
interposer card For
function DDR3 Thermal Testing Form gold fingers Power pin: VREFDQ, VTT, VDD, VREFCA, VDDSPD, VTT you can soldered a Current Sense Resistors(CSR) to DDR3 socket. |
| CV09DDR3-J1: with VDD Switch
Device Holes.
Option: +CSR x1 Add Current Sense Resistors(CSR) x1pcs |
| CV09DDR3-J2: (Discontinued)
CV09DDR3-J2v1.1 with VREFDQ, VTT, VDD, VREFCA, VDDSPD, VTT Switch Device Holes. CV09DDR3-J2v2(ODM version) with VREFDQ, VTT, VDD, VREFCA, VDDSPD, VTT Switch Device hole and bit 63-DQ63(pin 234), bit 62-DQ62(pin 233), bit 59-DQ59(pin 115) bit14-DQ14(pin 137) Switch Solder Pads. Option: +CSR x6 Add Current Sense Resistors(CSR) x6pcs |
 |
|
 |
 |
| DDR3 Open-Short test card | |
| CV11R-DDR3 | inquiry |
| CV11R-DDR3+DDR2 Option: +DDR2= CV09R-240S |
inquiry |
Function:
Did you ever burn your mother board, DDR3 DRAM Module, or other peripheral?
Too many circuits between mother board and DRAM Module, so if mother board dead,
shall test circuits open-short at first, it's helpful for repair.
Open-Short Test Card Merits:
1. Save money: Avoid mother board, DRAM Module, or other peripheral burned for
DRAM Module shortage circuit.
2. Save time: Open-Short test complete only take few minutes for DRAM Module pin to pin;
or circuits between mother board and DRAM Module.
3. Convenient: Easy use and carry.
4. Powerful:
a. Just test one-pin, can find out multi-pin shortage, it's helpfulness than Scope and Meter.
b. Test Open-Short no need Oscilloscope and Meter, because Scope very
difficult to distinguish Hi-level and VCC/VDD, Low-level and GND/VSS signal.
Others RAM/SDRAM/DDR/DDR2 Memory module series products
| Home | Index |   |
Start: 23/12/2007 Update: 08.26.2010