| PCI Express Mini/mPCIe bus series |
* PCI card plugged into connector figure
Attention:
1. Whole signals of bus Test Socket/Converter/Extender maybe not 100% one to one(1:1)
convert, please check specification.
2. No matter how many Slot/Socket on our board, PCI Express series only can use one Slot/Socket at a time.
3. All Converters/Test Socket/Riser card/Extender have Timing, Delay, Impedance,
Resistance Contact problem, so we can't guarantee can work 100%.
4. External converter card, if occur unstable, try to shorten the cable to better this status.
(Discontinued) |
||
 |
 |
|
 |
||
CV09Pe-mPe1 PCI Express to Mini PCI Express Converter(Discontinued)
CV09Pe-mPe1h *for Half-Mini Card Converter(Discontinued)
CV09Pe-mPe1v1.1 PCI Express to Mini PCI Express Converter
CV09Pe-mPe1hv1.1 *for Half-Mini Card Converter
v1.1 upgrade: the PETP0, PETN0, PERP0, PERN0, REFCLK+, REFCLK- signals
can be modified with a Solder Pads.
1. Insert Converter card into DeskTop mother board, for PCI Express Mini Card test,
can avoid the inconvenience to use NoteBook mother board.
2. The 52pin socket is 4.6mm height, and the PCB with two bare,
easy to measure Mini Card Front/Back side signals.
3. LED inductor : 3.3V, 1.5V, WAN, LAN, PAN
4. Schematics:
(Discontinued) |
(Discontinued) |
 |
CV09Pe-mPeNF simple mPCIe hot swapping/hot plugging converter(Discontinued)
CV09Pe-mPeNFv1.2
CV09Pe-mPeNFh *for Half-Mini Card(Discontinued)
CV09Pe-mPeNFhv1.2
1. Switch Mini PCI Express bus power source(+3.3v, +1.5v) ON-OFF,
Mini card can be inserted in Power-ON to do test, but must carefully to avoid signal or power shortage
and equipment damage.
2. LED inductor : 12V, 5V, 3.3V, 1.5V, WAN, LAN, PAN, WDIS, PRST, WAKE
3. Run real hot plugging function in operation system,
must write PCI express device configuration register Read/Writer program.
4. Option: +5V= Add one set 12V to 5V DC converter.
5. Option: +U= Add USB connector x2, without USB function,
only for power source +5V input or output.
6. Schematics:
CV09Pe-eMPe PCI Express external to Mini PCI Express Converter Card
CV09Pe-eMPeh *for Half-Mini Card
1. Insert Converter card into DeskTop mother board, for PCI Express Mini Card test,
can avoid the inconvenience to use NoteBook mother board.
2. The 52pin socket is 4.6mm height, and the PCB with two bare,
easy to measure Mini Card Front/Back side signals.
3. LED inductor : 12V, 5V, 3.3V, 1.5V, WAN, LAN, PAN, WDIS, PRST, WAKE
4. with cable length= 30cm
5. Schematics:
|
 |
 |
 |
 |
User can choose to combine the Base adapter, Target adapter, except the
CV09mPe-B1, CV09mPe-B2, the others can be modified to suit for Half-Mini Card.
Base adapter: CV09mPe-B1, CV09mPe-B2, CV09mPe-B3
Target adapter: CV09mPe-T1, CV09mPe-T2, CV09mPe-T3,CV09mPe-T4,
CV09mPe-T5
* 52pin socket with 4.6mm height, one part of PCB is bare,
easy to measure the whole Front/Back side signals of Mini Card.
CV09mPe-Pe Full mPCIe to PCIe converter
CV09mPeh-Pe Half mPCIe to PCIe converter
1. Can use this converter to insert PCI Express card into Mini PCI Express bus.
2. Use the attached Cable A, in order to input 12V power source for PCI Express bus.
3. LED inductor: 5V, 12V signal LED display.
4. +PH= add 40p Pin Head, in order to measure the Mini PCI Express bus signals.
5. +U= add USB connector and Cable B, in order to input 5V power source for USB.
6. Schematics:
 |
 |
 |
||
 |
 |
 |
 |
 |
CV09mPe-S1 Full mPCIe protector adapter
1a. Use this protector adapter to protect mother board's Mini PCI Express 52p socket.
CV09mPe-S1h Full to Half protector card
1b. Use this protector card to change mother board's Full-Mini Card Form to
Half-Mini Card Form.
2. LED inductor: 1.5V, GND signal LED display.
3. +NF= add Switch for Mini PCI Express bus power source(3.3v, 1.5v) ON-OFF,
can test Mini card in Power-ON(simple hot swapping/hot plugging card),
but must carefully to avoid signal or power shortage and equipment damage.
Run the hot swapping/hot plugging card in operation system,
must write PCI express device configuration register's Read/Writer program.
4. +U= add USB connector x2 and Cable B, in order to input 5V USB power source,
but only can choose one USB connector to use.
5. Schematics:
CV09mPe-S2 Full mPCIe protector adapter
1a. Use this protector adapter to protect mother board's Mini PCI Express 52p socket.
CV09mPe-S2h Full to Half protector adapter
1b. Use this protector adapter to change mother board's Full-Mini Card Form to
Half-Mini Card Form.
CV09mPeh-S2 Half to Full protector adapter
1c. Use this protector adapter to change mother board's Half-Mini Card Form to
Full-Mini Card Form.
2. LED inductor: 5V signal LED display.
3. +U= add USB connector and Cable B, in order to input 5V power source for USB.
4. Schematics:
CV09mPe-L(Left side) Full mPCIe protector adapter
1a. Use this protector adapter to protect mother board's Mini PCI Express 52p socket,
Mini Card insert from Left side.
CV09mPe-Lh Full to Half protector adapter
1b. Use this protector adapter to change mother board's
Full-Mini Card Form to Half-Mini Card Form.
CV09mPe-R(Right side) Full mPCIe protector adapter
1c. Use this protector adapter to protect mother board's Mini PCI Express 52p socket,
Mini Card insert from Right side.
CV09mPe-Rh Full to Half protector adapter
1d. Use this protector adapter to change mother board's Full-Mini Card Form to
Half-Mini Card Form.
2. LED inductor: 1.5V, GND signal LED display.
3. +NF= add Switch for Mini PCI Express bus power source(3.3v, 1.5v) ON-OFF,
can test Mini card in Power-ON(simple hot swapping/hot plugging card),
but must carefully to avoid signal or power shortage and equipment damage.
Run the hot swapping/hot plugging card in operation system,
must write PCI express device configuration register's Read/Writer program.
4. +U= add USB connector x2 and Cable B, in order to input 5V USB power source,
but only can choose one USB connector to use.
5. Schematics:
 |
|
 |
 |
CV09mPe-e1 Mini PCI Express external Mini PCI Express adapter
CV09mPe-e1h Full to Half external adapter
1. The Mini Card in external type for testing.
2. with cable length= 45cm(Option: length= 30cm)
3. +NF= add Switch for Mini PCI Express bus power source(3.3v, 1.5v) ON-OFF,
can test Mini card in Power-ON(simple hot swapping/hot plugging card),
but must carefully to avoid signal or power shortage and equipment damage.
Run the hot swapping/hot plugging card in operation system,
must write PCI express device configuration register's Read/Writer program.
4. +U= add USB connector x2 and Cable B, in order to input 5V USB power source,
but only can choose one USB connector to use.
5. Schematics:
CV09mPe-e2 Mini PCI Express external Mini PCI Express adapter
CV09mPe-e2h Full to Half external adapter
CV09mPeh-e2 Half to Full external adapter
CV09mPeh-e2h Half to Half external adapter
1. The Mini Card in external type for testing.
2. with cable length= 45cm(Option: length= 30cm).
3. +U= add USB connector and Cable B, in order to input 5V power source for USB,
4. Schematics:
| Home | Index |   |
Start: 01/08/2002 Update: 08.26.2010